Home > HARDWARE > CONSTRUCTION HARDWARE > GUTTER > PVC GUTTER
Sort By:
1 2 3
Debri-Shield AW202 Downspout Bracket DuraSpout AB202 Downspout Bracket Genova HRW108 Gutter Strap Hanger
Used to support DuraSpout downspout at either the offset elbow, coupler, or discharge spout. Never needs painting. Will not rust, rot or chip. Used to support DuraSpout downspout at either the offset elbow, coupler, or discharge spout. Never needs painting. Will not rust, rot or chip. Used where fascia board does not exist or is not vertical. Tang nailed under shingles then screwed to support brackets and slip joints. Front hinge snapped over button on part No.RW105 and part No.RW106.
Raingo RB202 Downspout Bracket Raingo RW202 Downspout Bracket DuraSpout AW302 Downspout Bracket
To support downspout at either the offset elbow coupler or discharge spout. (Estimated 70 pieces per 1000' of gutter) To support downspout at either the offset elbow coupler or discharge spout. (Estimated 70 pieces per 1000' of gutter) Used to support DuraSpout downspout at either the offset elbow, coupler, or discharge spout. Never needs painting. Will not rust, rot or chip.
Raingo AW201B Type B Downspout Elbow Raingo AB201B Type B Downspout Elbow Genova AW108 Repla K Gutter Strap Hander
Used with Repla K system or as a replacement for metal. Used where the downspout changes in any direction. Turns 112 degrees for offsets and discharge spouts. Used with Repla K system or as a replacement for metal. Used where the downspout changes in any direction. Turns 112 degrees for offsets and discharge spouts. Used where fascia board does not exist or is not vertical. Attaches to roof under shingles and screwed to support brackets.
DuraSpout AW203 Downspout Coupler DuraSpout AB203 Downspout Coupler Raingo AW221 Type A to B Downspout Elbow
Connects two lengths of downspout. Connects two lengths of downspout. Used with a B-style Elbow to create an offset on side of house.
Raingo AB221 Type A to B Downspout Elbow Genova AB101K Repla K Right Hand Gutter End Cap Genova AB102K Repla K Left Hand Gutter End Cap
Used with a B-style Elbow to create an offset on side of house. For end of gutter run. For end of gutter run.
Genova AW101K Repla K Right Hand Gutter End Cap Raingo RB201 Standard Downspout Elbow Raingo RW201 Standard Downspout Elbow
For end of gutter run. Used where the square downspout changes in any direction. Estimated 100 pieces per 1000' of gutter. Used where the square downspout changes in any direction. Estimated 100 pieces per 1000' of gutter.
Genova AW102K Repla K Left Hand Gutter End Cap Raingo RB106H Heavy Load Gutter Bracket Raingo RW106H Heavy Load Gutter Bracket
For end of gutter run. Basic gutter support fitting, installed every 30" of gutter length. Patented button on front for alternate use with part No. RW108. (Estimated 300 pieces per 1000' of gutter). Basic gutter support fitting, installed every 30" of gutter length. Patented button on front for alternate use with part No. RW108. (Estimated 300 pieces per 1000' of gutter).
Raingo RB101 Inside Gutter End Cap Raingo RB102 Outside Gutter End Cap Raingo RW102 Outside Gutter End Cap
Used with gutter fitting to make either right or left gutter stop. (Estimated 15 piece per 1000' of gutter). Used to terminate either right or left gutter end, complete with Raingo seal. (Estimated 45 pieces per 1000' of gutter). Used to terminate either right or left gutter end, complete with Raingo seal. (Estimated 45 pieces per 1000' of gutter).
Raingo RW101 Inside Gutter End Cap Genova AW106 Repla K Gutter Bracket Genova AB106 Repla K Gutter Bracket
Used with gutter fitting to make either right or left gutter stop. (Estimated 15 piece per 1000' of gutter). Used for support of gutter. Brackets can not be seen at ground level. Used for support of gutter. Brackets can not be seen at ground level.
Raingo RW209 Downspout Elbow Raingo RB209 Downspout Elbow Raingo AW301B Type B Downspout Elbow
90 degree angle. Non-metallic, never needs painting. Will not rust, rot or chip. Fits anywhere downspout changes direction. 90 degree angle. Non-metallic, never needs painting. Will not rust, rot or chip. Fits anywhere downspout changes direction. Used with Repla K system or as a replacement for metal. Used where the downspout changes in any direction. Turns 112 degrees for offsets and discharge spouts.
   
 
1 2 3